Enable CPU Sharing in ACRN

Introduction

The goal of CPU Sharing is to fully utilize the physical CPU resource to support more virtual machines. ACRN only supports 1 to 1 mapping mode between virtual CPUs (vCPUs) and physical CPUs (pCPUs). Because of the lack of CPU sharing ability, the number of VMs is limited. To support CPU Sharing, we have introduced a scheduling framework and implemented two simple small scheduling algorithms to satisfy embedded device requirements. Note that, CPU Sharing is not available for VMs with local APIC passthrough (--lapic_pt option).

Scheduling Framework

To satisfy the modularization design concept, the scheduling framework layer isolates the vCPU layer and scheduler algorithm. It does not have a vCPU concept so it is only aware of the thread object instance. The thread object state machine is maintained in the framework. The framework abstracts the scheduler algorithm object, so this architecture can easily extend to new scheduler algorithms.

../_images/cpu_sharing_framework.png

The below diagram shows that the vCPU layer invokes APIs provided by scheduling framework for vCPU scheduling. The scheduling framework also provides some APIs for schedulers. The scheduler mainly implements some callbacks in an acrn_scheduler instance for scheduling framework. Scheduling initialization is invoked in the hardware management layer.

../_images/cpu_sharing_api.png

CPU Affinity

We do not support vCPU migration; the assignment of vCPU mapping to pCPU is fixed at the time the VM is launched. The statically configured cpu_affinity in the VM configuration defines a superset of pCPUs that the VM is allowed to run on. One bit in this bitmap indicates that one pCPU could be assigned to this VM, and the bit number is the pCPU ID. A pre-launched VM is launched on exactly the number of pCPUs assigned in this bitmap. The vCPU to pCPU mapping is implicitly indicated: vCPU0 maps to the pCPU with lowest pCPU ID, vCPU1 maps to the second lowest pCPU ID, and so on.

For post-launched VMs, acrn-dm could choose to launch a subset of pCPUs that are defined in cpu_affinity by specifying the assigned Service VM vCPU’s lapic_id (--cpu_affinity option). But it can’t assign any pCPUs that are not included in the VM’s cpu_affinity.

Here is an example for affinity:

  • VM0: 2 vCPUs, pinned to pCPU0 and pCPU1

  • VM1: 2 vCPUs, pinned to pCPU0 and pCPU1

  • VM2: 2 vCPUs, pinned to pCPU2 and pCPU3

../_images/cpu_sharing_affinity.png

Thread Object State

The thread object contains three states: RUNNING, RUNNABLE, and BLOCKED.

../_images/cpu_sharing_state.png

After a new vCPU is created, the corresponding thread object is initiated. The vCPU layer invokes a wakeup operation. After wakeup, the state for the new thread object is set to RUNNABLE, and then follows its algorithm to determine whether or not to preempt the current running thread object. If yes, it turns to the RUNNING state. In RUNNING state, the thread object may turn back to the RUNNABLE state when it runs out of its timeslice, or it might yield the pCPU by itself, or be preempted. The thread object under RUNNING state may trigger sleep to transfer to BLOCKED state.

Scheduler

The below block diagram shows the basic concept for the scheduler. There are four kinds of schedulers in the diagram: NOOP (No-Operation) scheduler, the IO sensitive Round Robin scheduler, the priority based scheduler and the BVT (Borrowed Virtual Time) scheduler. By default, BVT is used.

  • No-Operation scheduler:

    The NOOP (No-operation) scheduler has the same policy as the original 1-1 mapping previously used; every pCPU can run only two thread objects: one is the idle thread, and another is the thread of the assigned vCPU. With this scheduler, vCPU works in Work-Conserving mode, which always tries to keep resources busy, and will run once it is ready. The idle thread can run when the vCPU thread is blocked.

  • Priority based scheduler:

    The priority based scheduler can support vCPU scheduling based on their pre-configured priorities. A vCPU can be running only if there is no higher priority vCPU running on the same pCPU. For example, in some cases, we have two VMs, one VM can be configured to use PRIO_LOW and the other one to use PRIO_HIGH. The vCPU of the PRIO_LOW VM can only be running when the vCPU of the PRIO_HIGH VM voluntarily relinquishes usage of the pCPU.

  • Borrowed Virtual Time scheduler:

    BVT (Borrowed Virtual time) is a virtual time based scheduling algorithm, it dispatches the runnable thread with the earliest effective virtual time.

    • Virtual time: The thread with the earliest effective virtual time (EVT) is dispatched first.

    • Warp: a latency-sensitive thread is allowed to warp back in virtual time to make it appear earlier. It borrows virtual time from its future CPU allocation and thus does not disrupt long-term CPU sharing

    • MCU: minimum charging unit, the scheduler account for running time in units of MCU.

    • Weighted fair sharing: each runnable thread receives a share of the processor in proportion to its weight over a scheduling window of some number of MCU.

    • C: context switch allowance. Real time by which the current thread is allowed to advance beyond another runnable thread with equal claim on the CPU. C is similar to the quantum in conventional timesharing.

Scheduler configuration

  • The scheduler used at runtime is defined in the scenario XML file via the hv.FEATURES.SCHEDULER option. The default scheduler is SCHED_BVT. Use the ACRN Configurator tool if you want to change this scenario option value.

The default scheduler is SCHED_BVT.

  • The cpu_affinity could be configured by one of these approaches:

    • Without cpu_affinity option in acrn-dm. This launches the user VM on all the pCPUs that are included in the statically configured cpu_affinity.

    • With cpu_affinity option in acrn-dm. This launches the user VM on a subset of the configured cpu_affinity pCPUs.

    For example, assign physical CPUs 0 and 1 to this VM:

    --cpu_affinity 0,1

Example

Use the following settings to support this configuration in the shared scenario:

pCPU0

pCPU1

pCPU2

pCPU3

Service VM + WaaG

RT Linux

  • offline pcpu2-3 in Service VM.

  • launch guests.

    • launch WaaG with “–cpu_affinity 0,1”

    • launch RT with “–cpu_affinity 2,3”

After you start all VMs, check the CPU affinities from the Hypervisor console with the vcpu_list command:

ACRN:\>vcpu_list

VM ID    PCPU ID    VCPU ID    VCPU ROLE    VCPU STATE    THREAD STATE
=====    =======    =======    =========    ==========    ==========
  0         0          0       PRIMARY      Running          RUNNING
  0         1          1       SECONDARY    Running          RUNNING
  1         0          0       PRIMARY      Running          RUNNABLE
  1         1          1       SECONDARY    Running          BLOCKED
  2         2          0       PRIMARY      Running          RUNNING
  2         3          1       SECONDARY    Running          RUNNING

Note: the THREAD STATE are instant states, they will change at any time.