Using PREEMPT_RT-Linux for real-time UOS

The ACRN project uses various techniques to support a User OS (UOS) running as virtual machine (VM) with real-time characteristics, also called a “RTVM” in ACRN terminology. Some of these techniques include device passthrough and cache allocation technology (CAT), as shown in Figure 225.

To benefit from these techniques, the OS running in the VM should also behave as a real-time system. In this tutorial, we explain how to run a Privileged VM based on a modified Clear Linux* OS using PREEMPT_RT real-time kernel patches from the Real-Time Linux collaborative project.

The PREEMPT_RT patch add preemption models to the mainline Linux kernel. The “Fully Preemptible Kernel” model is the one that turns Linux into an RTOS, allowing the system to react to an external event such as an interrupt within a defined time frame.

Figure 225 Real-Time Linux (PREEMPT_RT) VM on ACRN

The RTVM exclusively owns its passthrough devices, so in addition to the controller and file system used by the SOS, a dedicated storage controller and device are needed to host the RTVM’s root filesystem. The two storage devices should be under different PCI controllers because the system can only pass through PCI-based devices to a guest OS. The Intel NUC7ixDNHE NUC (KBL) is a good platform to set up a real-time system because it has both an NVMe and a SATA controller. You will need both NVMe and SATA storage devices in order to proceed.

The following procedures show an example for setting up a real-time system on Intel KBL NUC with a SATA SSD as /dev/sda and an NVME SSD as /dev/nvme0n1p.

1. Follow the Set up a Clear Linux Operating System instructions in the Getting started guide for Intel NUC to:

   1. Install Clear Linux (version 29400 or higher) onto the NVMe
   2. Install Clear Linux (version 29400 or higher) onto the SATA SSD
   3. Set up Clear Linux on the SATA SSD as the Service OS (SOS) following the Add the ACRN hypervisor to the EFI Partition instructions in the same guide.

2. Set up and launch a Real-Time Linux guest

   1. Add kernel-lts2018-preempt-rt bundle (as root):

      # swupd bundle-add kernel-lts2018-preempt-rt
      

   2. Copy preempt-rt module to NVMe disk:

      # mount /dev/nvme0n1p3 /mnt
      # ls -l /usr/lib/modules/
      4.19.31-6.iot-lts2018-preempt-rt/
      4.19.36-48.iot-lts2018/
      4.19.36-48.iot-lts2018-sos/
      5.0.14-753.native/
      # cp -r /usr/lib/modules/4.19.31-6.iot-lts2018-preempt-rt /mnt/lib/modules/
      # cd ~ && umount /mnt && sync
      

   3. Get your NVMe pass-through IDs (in our example they are [01:00.0] and [8086:f1a6]):

      # lspci -nn | grep SSD
      01:00.0 Non-Volatile memory controller [0108]: Intel Corporation SSD Pro 7600p/760p/E 6100p Series [8086:f1a6] (rev 03)
      

   4. Modify launch_hard_rt_vm.sh script:

      # vim /usr/share/acrn/samples/nuc/launch_hard_rt_vm.sh
      
      <Modify the passthru_bdf and passthru_vpid with your NVMe pass-through IDs>
      
      passthru_vpid=(
      ["eth"]="8086 156f"
      ["sata"]="8086 9d03"
      )
      passthru_bdf=(
      ["eth"]="0000:00:1f.6"
      ["sata"]="0000:00:17.0"
      )
      
      TO:
      passthru_vpid=(
      ["eth"]="8086 156f"
      ["sata"]="8086 f1a6"
      )
      passthru_bdf=(
      ["eth"]="0000:00:1f.6"
      ["sata"]="0000:01:00.0"
      )
      
      <Modify NVMe pass-through id>
      
      -s 2,passthru,0/17/0 \
      
      TO:
      -s 2,passthru,01/00/0 \
      
      <Modify rootfs to NVMe>
      
      -B "root=/dev/sda3 rw rootwait maxcpus=$1 nohpet console=hvc0 \
      
      TO:
      -B "root=/dev/nvme0n1p3 rw rootwait maxcpus=$1 nohpet console=hvc0 \
      

3. Get IP address in real-time VM if you need it (There is no IP by default)

   1. Method 1 virtio-net NIC:

      # vim /usr/share/acrn/samples/nuc/launch_hard_rt_vm.sh
      
      <add below line into acrn-dm boot args>
      
      -s 4,virtio-net,tap0 \
      

   2. Method 2 pass-through NIC:

      <Get your ethernet IDs first(in our example they are ``[00:1f.6]`` and ``[8086:15e3]``)>
      
      # lspci -nn | grep Eth
      00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (5) I219-LM [8086:15e3]
      
      # vim /usr/share/acrn/samples/nuc/launch_hard_rt_vm.sh
      
      <Modify the passthru_bdf and passthru_vpid with your ethernet IDs>
      
      passthru_vpid=(
      ["eth"]="8086 156f"
      ["sata"]="8086 f1a6"
      )
      passthru_bdf=(
      ["eth"]="0000:00:1f.6"
      ["sata"]="0000:01:00.0"
      )
      
      TO:
      passthru_vpid=(
      ["eth"]="8086 15e3"
      ["sata"]="8086 f1a6"
      )
      passthru_bdf=(
      ["eth"]="0000:00:1f.6"
      ["sata"]="0000:01:00.0"
      )
      
      <Uncomment the following three lines>
      
      #echo ${passthru_vpid["eth"]} > /sys/bus/pci/drivers/pci-stub/new_id
      #echo ${passthru_bdf["eth"]} > /sys/bus/pci/devices/${passthru_bdf["eth"]}/driver/unbind
      #echo ${passthru_bdf["eth"]} > /sys/bus/pci/drivers/pci-stub/bind
      
      TO:
      echo ${passthru_vpid["eth"]} > /sys/bus/pci/drivers/pci-stub/new_id
      echo ${passthru_bdf["eth"]} > /sys/bus/pci/devices/${passthru_bdf["eth"]}/driver/unbind
      echo ${passthru_bdf["eth"]} > /sys/bus/pci/drivers/pci-stub/bind
      
      <add below line into acrn-dm boot args,behind is your ethernet ID>
      
      -s 4,passthru,00/1f/6 \
      

   Note

   method 1 will give both the Service VM and User VM network connectivity

   method 2 will give the User VM a network interface, the Service VM will loose it

4. Start the Real-Time Linux guest:

   # sh /usr/share/acrn/samples/nuc/launch_hard_rt_vm.sh
   

5. At this point, you’ve successfully launched the real-time VM and Guest OS. You can verify a preemptible kernel was loaded using the uname -a command:

   root@rtvm-02 ~ # uname -a
   Linux clr-de362ed3fd444586b99968b5ceb22275 4.19.31-6.iot-lts2018-preempt-rt #1 SMP PREEMPT Mon May 20 16:00:51 UTC 2019 x86_64 GNU/Linux
   

6. Now you can run all kinds of performance tools to experience real-time performance. One popular tool is cyclictest. You can install this tool and run it with:

   swupd bundle-add dev-utils
   cyclictest -N -p80 -D30 -M > log.txt
   cat log.txt
   

7. To achieve better real-time performance, the following is the recommended BIOS setting. You may not see all the settings because some of them may be hidden by different BIOS vendors.

   Table 13 Recommended BIOS Settings

   Item	Setting
   VMX	Enabled
   VT-d	Enabled
   Hyper-Threading	Disabled
   Speed Step	Disabled
   Speed Shift	Disabled
   C-State	Disabled
   Voltage Optimization	Disabled
   GT RC6	Disabled
   Gfx Low Power Mode	Disabled
   SA GV	Disabled
   Aggressive LPM Support	Disabled
   ACPI S3 Support	Disabled
   Native ASPM	Disabled